PERMABOND® MH052 Anaerobic Threadsealant

Permabond® MH052 Anaerobic Threadsealant is ideal for the sealing of threaded joints. It is approved for use with natural gas and LPG and also for gaseous oxygen.

PERMABOND® MH052 Anaerobic Threadsealant

Permabond® MH052 is ideal for the sealing of threaded joints. It is approved for use with natural gas and LPG for working pressure up to 20 bar (290 psi) and also for gaseous oxygen up to 10 bar (145 psi) and 60°C. MH052 seals against gas, water, LPG, hydrocarbons, oils and other chemicals and will seal to the burst rating of the pipe. Unlike PTFE tape or hemp, Permabond MH052 will not shred or dry out, so it will provide a durable seal, helping to extend the life of the components.

Features & Benefits

  • Excellent chemical resistance
  • Pressure seal to burst rating of pipe
  • No loose particles to clog valves
  • Approved for use with gaseous oxygen
  • WRAS listed for contact with wholesome (potable) water
  • DVGW & BAM approval

 

Physical Properties of Uncured Adhesive

  • Chemical composition: Acrylic
  • Appearance: Yellow
  • Viscosity @ 25°C: 2rpm: 65,000 mPa.s (cP)
    20rpm: 25,000 mPa.s (cP)
  • Specific Gravity: 1.1
  • UV fluorescence: Yes

Typical Curing Properties

  • Maximum gap fill: 0.5 mm
    M56
  • Time taken to reach handling strength (M10 steel) @23°C: 15 minutes*
  • Time taken to reach working strength (M10 steel) @23°C: 1-3 hours
  • Full strength (M10 steel) @23°C: 24 hours

Typical Performance of Cured Adhesive

  • Torque strength (M10 steel ISO10964): Break 20 N·m 180 in.lb
    Prevail 11 N·m 100 in.lb
  • Shear strength (steel collar & pin ISO10123): 10 MPa 1450 psi
  • Coefficient of thermal expansion: 90 x 10-6 mm/mm/°C
  • Dielectric strength: 11 kV/mm
  • Thermal conductivity: 0.19 W/(m.K)

Surface Preparation

Though the anaerobic adhesives will tolerate a slight degree of surface contamination, best results are obtained on clean, dry and grease free surfaces. The use of a suitable solvent-based cleaner (such as acetone or isopropanol) is recommended.
In general, roughened surfaces (~25μm) give higher bond strengths than polished or ground surfaces.
To reduce the curing time, especially on inactive surfaces (such as zinc, aluminium and stainless steel), the use of Permabond A905 or ASC10 can be considered.

Directions for Use

1) Apply a continuous bead circumferentially 1-2 threads from the leading edge.
2) Ensure sufficient is applied to give a complete seal.
3) For taper/parallel threads ensure adhesive is positioned where the threads will engage fully. Gaps, and therefore cure times, may be greater than expected with this joint configuration.
4) Tighten with normal tools.

TDS / MSDS

To request any type of technical sheet or safety sheet.

Product Categories

TDS / MSDS

To request any type of technical sheet or safety sheet.

Can't find the right product?

Talk to a Technical Representative

Need advice?

Our technical team can provide assistance on your industrial product or application needs. Please complete the enquiry form below and we will contact you within 24-48 hours.

Request a quote

Please send us your request to receive a customised offer, either for specific products or special requirements.

Technical Data sheet and safety data sheet

Please fill in the form to receive the .pdf document.